SpanishEnglish

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Guaranteeing corporate office connection is critical. Redundant copper and fibre access points are useful but the problem is that different fixed access points usually share an infrastructure meaning that there is a risk of simultaneous loss of both. However, mobile networks connect through the air, have a different infrastructure to fixed networks and are highly efficient in terms of 4G latency and speed, which makes them the ideal backup system.

Teldat-4Ge enables mobile connection of corporate routers that do not come with embedded mobile connections or are installed in communications cabinets with poor coverage, in a non-intrusive manner, as Teldat-4Ge is a peripheral router device that maintains a secure communications and control solution. It may operate autonomously.

Ensuring connectivity for a corporation's offices is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system.

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device.

Ensuring connectivity for a corporation's offices is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system.

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device.

Ensuring connectivity for a corporation's office is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system. 

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device. 

Ensuring connectivity for a corporation's office is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system. 

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device. 

Ensuring connectivity for a corporation's office is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system. 

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device. 

Ensuring connectivity for a corporation's office is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system. 

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device. 

Ensuring connectivity for a corporation's office is essential. While redundant copper or fiber connections are useful, different fixed access methods often share the same infrastructure which means there is a chance they might fail at the same time. By contrast, mobile networks use air as a medium and a different infrastructure to fixed networks. This, together with the high level of efficiency of 4G networks in terms of latency and speed, make them the ideal backup system. 

Teldat-4Ge provides a non-intrusive way to enable mobile access in corporate routers that do not natively support mobile connections or that are installed in communications cabinets with poor coverage. Teldat-4Ge is a peripheral device that works with the router to secure and maintain control over the communications. It can operate as a standalone device. 

  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.




  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-1
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power, LAN and mobile network connection
  • Quick ansd easy installation
  • Requires no previous configuration, only Ethernet connection (with PoE enabled, only Ethernet cable is required, otherwise it must be connected to the mains).
  • No management required
  • Download configuration using self-provisioning (similar to an IP phone). Configuration is normally stored in the office router.
  • The corporate router keeps control
  • The mobile connection is controlled and the same connection, security and service quality policies as the fixed connection apply.
  • Discreet and inconspicuous design
  • It is usually installed in an inconspicuous spot on an interior office wall to achieve maximum coverage.

    Teldat-4Ge is the quickest, most efficient and versatile way to achieve a quality 3G/4G connection.

    Suitability of mobile networks as backup connections is unquestionable although corporate routers are not usually prepared for this or are installed in places where mobile network coverage is very poor. Teldat-4Ge is the solution to these problems as it is a small device suitable for installation in a place in the office that provides adequate coverage and connects to the corporate router via Ethernet.

    The mobile connection is directly controlled by the same already-existing corporate router so that it is integrated in the network security, service quality and management policy (it may operate autonomously)

    Teldat-4Ge is efficiently and securely installed in a few minutes without the need for qualified personnel due to self-provisioning and PoE.

    Use of a mobile network as backup for a fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Existing router peripheral device


    Autonomous mobile network connection for network and device backup.

    Figure 2: Independent mobile router

  • Provides any existing architecture with mobile access
  • Mobile and fixed connections are controlled by the same router, following the same security or service quality policies as the latter.

  • Standard-based
  • VLAN is used to establish the data connection between the router and Teldat-4Ge, meaning that it is a virtual interface in the router for all effects and purposes.

  • Self-provisioning
  • Teldat-4Ge does not store configuration but receives it via DHCP during start-up so no action needs to be performed on the device prior to its installation.

  • No management required
  • No management address needs to be reserved or activated in management systems as it is manageable from the existing router.

  • Installation with one single cable
  • All that is required is an Ethernet connection with PoE (PoE injector available in case the switch does not provide PoE). Easy and quick to install.

  • installation on a table or wall
  • Designed for installation on a wall to achieve the best signal.

  • Specifically designed for installation in offices
  • It is a small insignificant device that remains inconspicuous in work rooms or transit areas.

  • It may be used as an autonomous router
  • "Router mode" where a mobile connection is provided directly to Ethernet devices for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • Gigabit Ethernet 10/100/1000 interface with the local network
    • RJ45 connector
    • Two external antennas
    • Dual antenna for LTE MIMO reception
    • SMA connector
    • Dimensions and Weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: On a table, wall and DIN track
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Self-provisioning
    • Reception of parameters via DHCP
    • The office router is normally the DHCP server
    • Install and ready
    • Communication with the router
    • Connection to the router via VLAN
    • Use of the existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, Policy based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1,v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • encrypted: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • Detection of DoS and DDoS attacks
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Management of phone terminals with SIP protocol
    • Service quality
    • Classification, marking, BW management, BW prioritisation and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), according weight/type (WFQ, CBWFQ)
    • IPv6.
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Remote Wireshark compatible traffic collection

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required. Connect to Ethernet and ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up.  This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required. Connect to Ethernet and ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up.  This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required, just connect to Ethernet and it´s ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up. This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required, just connect to Ethernet and it´s ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up. This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required, just connect to Ethernet and it´s ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up. This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required, just connect to Ethernet and it´s ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up. This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
  • Quick and easy installation
  • No configuration required, just connect to Ethernet and it´s ready to go. If PoE is enabled, you only need the Ethernet cable; if not, you'll need to plug it.

  • No management required
  • The device uses auto provisioning to download the configuration (similar to an IP phone) from the office router.

  • The corporate router maintains control
  • The router controls the mobile connection, applying the same connection, security and QoS policies used for the fixed connection.

  • Discreet, unobtrusive design
  • To achieve maximum coverage, the device is usually placed somewhere on a wall inside the office where it can go unnoticed.

    Teldat-4Ge is the fastest, most effective and versatile solution for quality 3G/4G mobile connectivity.

    Mobile networks are unquestionably the ideal backup connectivity solution where wired networks are unavailable. However, corporate routers are not usually prepared to handle a wireless connection or are housed in locations where mobile network coverage is lousy. Teldat-4Ge provides the solution to these problems. The device’s compact design makes it ideal for placing inside the office for optimum coverage and it connects to the corporate router via Ethernet.

    The existing corporate router directly controls the mobile connection and integrates it with security, QoS and network management policies (Teldat-4Ge can operate as a standalone device).

    With automatic provisioning and Power over Ethernet support, Teldat-4Ge can be efficiently and securely installed in just a few minutes, without requiring qualified personnel.

    Using the mobile network to back up the fixed network, integrating both connections into the same network infrastructure.


    Figure 1: Peripheral device for the existing router


    Autonomous mobile network connection for network and device backup.

    Figure 2: Autonomous mobile router

  • Integrates mobile access into existing architecture
  • The router managing the fixed connections also controls the mobile connections and therefore applies the same security and QoS policies. 

  • Standards-based
  • A VLAN is used to set up the data connection between the router and Teldat-4Ge, creating what is, for all intents and purposes, a virtual interface on the router.

  • Automatic provisioning
  • Teldat-4Ge does not store the configuration, rather it receives it via DHCP during start-up. This means that you do not need to do anything to the device before physically installing it.

  • No management required
  • The device can be managed from the existing router, so you do not need to reserve an address for managing the device or register it on the management systems.

  • Installation using a single cable
  • With Power over Ethernet support (a PoE injector is available for non-PoE switches) it can be powered simply using a single Ethernet cable making installation quick and easy.

  • Tabletop to wall installation
  • Designed to be mounted on a wall to get the best signal strength.

  • Specifically designed to be placed inside the office
  • The device goes unnoticed in work/transit areas thanks to its compact size and elegant design.

  • Standalone router option
  • In "Router mode" it provides Ethernet devices with mobile connectivity for mobile offices or device backup.

  • HARDWARE TECHNICAL FEATURES

    • Gigabit connection to the local network
    • 10/100/1000 Gigabit Ethernet interface to the local network
    • RJ45 connector
    • Two external antennas
    • Dual MIMO antenna for LTE reception
    • SMA connector
    • Dimensions and weight
    • Length x Width x Height: 160 x 145 x 45 mm
    • Approximate weight: 0,263 Kg
    • Format: Desktop, wall and DIN rail
    • Environmental specifications
    • Temperature: 0 to 45 ºC
    • Relative humidity: 5 to 90%
    • Atmospheric pressure: 700 to 1060 mbars

    SOFTWARE TECHNICAL FEATURES

    • Auto-provisioning
    • Parameters received via DHCP
    • The office router is normally the DHCP server
    • Install and ready to go
    • Communication with the router
    • Connection to the router via VLAN
    • Use of existing Ethernet infrastructure
    • Manageable from the router
    • IP protocol
    • ARP, ARP Proxy, MTU discovery, NAT, ECMP, BFD
    • RIP, OSPF, BGP, policy-based static and dynamic routing
    • Virtual Router Forwarding (Multi-VRF)
    • IP protocol (2)
    • Multicast: IGMP (v1, v2, v3), PIM-SM, MSDP, MLD, MLDv2
    • IPSLA service probes (delay, package loss, jitter)
    • High availability: VRRP, TVRP (HSRP compatible)
    • Security
    • IPSec support in transport and tunnel mode
    • Pre-shared authentication, RSA, Certificates, MDS, SHA-2
    • Encryption: DES (56 bits), 3DES (168 bits), AES (128, 192 and 256 bits)
    • Security (2)
    • Certificates: CSR, SCEP, X.509v3, PKIX, LDAP revocation
    • Static and dynamic access lists and session-based Firewall
    • DoS and DDoS detection
    • IP services
    • DHCP, DNS, FTP, SFTP, SSH, Telnet server and client
    • NTP, LDAP, Syslog, SCP client. TFTP Server, DHCP Relay , dynDNS
    • Phone terminal management using with SIP
    • Quality of service
    • Classification, marking, BW management, BW prioritization and limitation
    • Up to 32 types 16 queues per interface
    • Strict policies (PQ), Low latency (LLQ), by weight/type (WFQ, CBWFQ)
    • IPv6
    • Dual Stack, IP6oIPv4, IPv4oIPv6, GRE, 6rd, DHCPv6, ICMPv6, SLAAC
    • Static and dynamic routing RIPng, OSPFv3, MP-BGP
    • Multicast: MLD, MLDv2, Listener, Querier
    • Management
    • Netflow, RMON V5 and V9, SNMPv1, v2c y v3, Syslog support
    • Manageable via SMS
    • Wireshark-compatible remote traffic capture

    ADDITIONAL TECHNICAL FEATURES

    • LEDs
    • Power supply, LAN and mobile network connection
    Contact us
    X