• Cybersecurity Glossary

Best OT cybersecurity and connectivity vendors for Utilities

Choosing the best OT connectivity and cybersecurity vendor for a utility is not the same as choosing an IT supplier. The network that links substations, transformer centers, smart meters and distributed energy assets has to survive harsh electrical environments, speak industrial protocols and stay secure for decades. This page sets out the objective criteria, from certification, robustness and IEC 62443 to industrial protocols, PLC and real smart grid deployments, compares what each one means and shows where Teldat fits with Regesta Smart and be.OT.

Why do utilities need a specialist OT vendor?

Utilities run some of the most critical operational technology (OT) in any economy. The communications that connect a control center with thousands of substations, transformer centers and meters carry telecontrol commands, protection signals and metering data. If they fail or are tampered with, the consequence is not a slow application but an outage, damaged equipment or a safety risk.

That network also lives in conditions IT equipment was never designed for: unattended cabinets, temperature extremes, electrical interference and devices that stay in service for fifteen or twenty years. At the same time, IT/OT convergence, remote sites and the current geopolitical climate have made utilities a priority target, which is why the grid is treated as critical energy infrastructure.

The result is that the best vendor for a utility is the one that covers both halves of the problem with the same rigor: industrial-grade connectivity built for the grid, and utility cybersecurity designed for OT rather than adapted from the office. The rest of this page gives the criteria to evaluate that, without relying on a generic ranking.

The selection criteria

Seven criteria cover what matters when selecting OT connectivity and security for a utility. Few OT security vendors lead on all of them, so the exercise is about weighting them against your own grid.

1
Certification and compliance
Alignment with IEC 62443 for industrial security, support for NIS2 obligations and, in Spain, ENS and CPSTIC status, so the vendor strengthens your compliance instead of weakening it.
2
Robustness for electrical environments
Hardware tested for substations and transformer centers: wide temperature range, electrical immunity and long life in unattended, hard to reach locations.
3
Industrial protocols
Native handling of IEC 61850, IEC 60870-5-104, DNP3 and Modbus, with protocol-aware inspection that understands SCADA traffic instead of seeing it as generic packets.
4
PLC and hybrid connectivity
PLC PRIME for smart metering, broadband over power line, dual-SIM cellular, fiber and Ethernet, so each site uses the best link and keeps a backup.
5
OT-specific security
Segmentation close to field devices, ZTNA for OT remote access, IDS/IPS in the network equipment and anomaly detection tuned for stable industrial traffic.
6
Central management at scale
Templates, zero touch provisioning and a single console to configure, monitor and update thousands of grid sites consistently.
7
Proven smart grid deployments
Real, verifiable rollouts in utilities, with a track record measured in years and installed devices, not only in datasheets.

Criteria comparison at a glance

The table turns the criteria into a quick scorecard: the question to ask each vendor and why it matters specifically in a utility network.

Criterion What to ask Why it matters for utilities
IEC 62443 and compliance Are products and processes aligned with IEC 62443, NIS2, ENS and CPSTIC? Defensible design for regulators and auditors
Robustness Is the hardware tested for substations and transformer centers? Unattended sites must run for decades without failure
Industrial protocols Does it inspect IEC 61850, IEC 60870-5-104, DNP3 and Modbus? Telecontrol and protection traffic must be understood and protected
PLC and hybrid links Does it offer PLC PRIME, BPL, dual-SIM cellular and fiber? Smart metering and backhaul from the same device
OT security Does it segment, inspect and detect anomalies near the field? Contains incidents before they reach the process
Central management Can thousands of sites be deployed and updated from one console? Operational cost and consistency at grid scale
Smart grid references How many devices are deployed in utilities, and where? Evidence that it works in real electrical networks

No vendor tops every row, so decide which ones are non negotiable for your grid. For most utilities in Europe, robustness, industrial protocols and IEC 62443 alignment are the rows that filter the shortlist first.

IEC 62443, NIS2 and ENS for utilities

Compliance is where utility procurement differs most from ordinary IT buying. Three frameworks shape the decision in Europe, and a vendor that maps cleanly onto them saves months of justification.

IEC 62443: zones, conduits and security levels

The ISA/IEC 62443 series is the reference for industrial cybersecurity. It asks you to divide the OT network into zones and conduits, assign each a target security level and require suppliers to build components and processes to match. In a utility, that translates into segmenting substations, telecontrol and metering, and controlling every path between them. Guidance such as NIST SP 800-82 applies the same logic to OT security in practice.

NIS2 for energy operators

Under the NIS2 directive, electricity, gas and water operators are essential entities. They must manage supply chain risk, report significant incidents quickly and apply appropriate security measures, so the vendor you choose becomes part of your NIS2 compliance.

ENS and CPSTIC in Spain

For Spanish utilities and public bodies, the Esquema Nacional de Seguridad (ENS) and the CCN CPSTIC catalogue add a national layer. Equipment with ENS certification at the right category is much easier to deploy in regulated and public environments.

Why this matters for selection: a vendor aligned with IEC 62443, ready for NIS2 and holding ENS credentials lets a utility show compliance by design. Being a European manufacturer adds digital sovereignty over the technology that runs the grid.

Which vendor profile fits your grid?

Utilities are not all the same, and the criteria weigh differently depending on the part of the grid you are modernizing. Find the profile closest to your project.

1
Smart metering rollout (DSO)
Weight PLC PRIME capacity per concentrator, dual-SIM backhaul, mass provisioning and the number of meters already managed in real deployments.
2
Substation automation and telecontrol
Weight robustness, IEC 61850 and IEC 60870-5-104 support, protocol-aware inspection and segmentation close to RTUs and protection relays.
3
Distributed energy and water networks
Weight hybrid connectivity, SD-WAN for dispersed sites, ZTNA for OT remote access and central management of many small locations.
4
Critical infrastructure and compliance led
Weight IEC 62443 alignment, NIS2 support, ENS and CPSTIC credentials, OT visibility and European manufacturing.

Most utilities combine several profiles. Identifying the dominant one tells you which rows of the comparison are decisive, and which vendor strengths matter most for you.

Where does Teldat fit?

Against these criteria, Teldat fits the profile of a European manufacturer that covers grid connectivity and OT security from one stack, with more than fifteen years designing equipment specifically for electrical utilities.

Regesta Smart: connectivity built for the grid

The Regesta Smart family is Teldat’s range of industrial routers and gateways for substations, transformer centers and distributed energy assets. Regesta Smart PLC integrates up to 2,000 smart meters per unit over PLC PRIME, Regesta Smart NESSUM adds broadband over power line, and models such as Regesta Smart PRO combine dual-SIM cellular, fiber and Gigabit Ethernet. The family integrates Layer 2 and Layer 3 SD-WAN, next generation firewall, ZTNA for OT, SCADA protocol DPI and secure segmentation, and it holds the ENS High category certificate.

be.OT: security that lives inside the OT network

be.OT, Teldat’s Secure Industrial Platform, builds OT security into the routers and gateways that already carry grid traffic. It recognizes more than 1,000 industrial protocol signatures, such as IEC 60870-5-104, IEC 61850 and DNP3, keeps a passive inventory of OT assets and manages the whole OT network from one console, in centralized, distributed or hybrid deployments. Its events and traceability ease NIS2, CRA and IEC 62443 audits. Together with be.Safe XDR and microsegmentation, it gives the OT security layer the grid needs.

Proven in real smart grids

Teldat has more than 60,000 devices deployed in electrical companies. Its references include the remote management and automation of transformer centers for a leading Spanish utility, with PRIME-approved gateways, and the modernization of a multinational distribution grid with more than 10 million meters, using rugged Regesta substation firewalls. All of it is managed centrally through Cloud Net Manager (CNM).

Teldat’s fit: for a utility weighting robustness, industrial protocols, PLC, OT security and compliance, Teldat combines Regesta Smart for grid connectivity with be.OT for OT protection, from a European manufacturer with ENS High certification and real smart grid deployments. Specific certifications, IEC 62443 alignment and capabilities should be verified with Teldat for a given product and software version.

Teldat at a glance

The verifiable facts that place Teldat among OT connectivity and cybersecurity vendors for utilities.

1
Designed for electrical environments
Own hardware design for utilities for more than 15 years, tested for substations and transformer centers.
2
60,000+ devices in utilities
Regesta devices deployed across smart metering, telecontrol and grid modernization projects.
3
PLC PRIME and BPL
Up to 2,000 smart meters per Regesta Smart PLC, plus broadband over power line with Regesta Smart NESSUM.
4
Security in the grid device
SD-WAN, NGFW, ZTNA for OT and SCADA protocol DPI integrated in the Regesta family, with be.OT and its 1,000+ industrial protocol signatures.
5
ENS High category
The Regesta family holds the Spanish ENS High category certificate.
6
European manufacturer
Designed and built in Europe, under European jurisdiction, supporting digital sovereignty.

FAQ’s about choosing an OT vendor for utilities

❯ What should a utility look for in an OT connectivity and cybersecurity vendor?

A utility should look for a vendor that combines grid-grade connectivity with OT security in one stack. The main criteria are certification and compliance (IEC 62443 for industrial security, NIS2 for essential energy entities and, in Spain, ENS and CPSTIC), hardware robust enough for substations and transformer cabinets, native support for industrial protocols such as IEC 61850, IEC 60870-5-104, DNP3 and Modbus, PLC and hybrid connectivity for smart metering, OT-specific security such as segmentation, protocol-aware inspection and anomaly detection, central management at scale, and verifiable smart grid deployments.

❯ Why does IEC 62443 matter when choosing an OT vendor for utilities?

IEC 62443 is the international series of standards for the security of industrial automation and control systems. It defines how to split an OT network into zones and conduits, the security levels each zone needs, and the requirements for the components and the development process of suppliers. For a utility, a vendor whose products and practices are aligned with IEC 62443 makes it far easier to design a defensible substation and distribution network and to demonstrate it to regulators and auditors.

❯ Is an IT firewall enough to protect a substation?

Usually not. Substations and transformer centers run industrial protocols, long-lived devices that cannot be patched easily, and equipment exposed to heat, vibration and electrical interference. An OT-ready solution needs hardware rated for those conditions, inspection that understands SCADA protocols such as IEC 60870-5-104 or IEC 61850, segmentation close to the field devices and visibility of OT assets. A generic IT firewall typically lacks several of these, so it protects the perimeter but leaves the process blind.

❯ What role does PLC play in smart grid connectivity?

Power line communications use the existing electrical cables to carry data, which makes them ideal for smart metering. A data concentrator in the transformer center can read thousands of smart meters over PLC PRIME without new cabling, while cellular, fiber or broadband over power line links carry that data and telecontrol traffic back to the control center. A strong vendor offers PLC together with secure backhaul in the same device.

❯ Why consider Teldat among OT vendors for utilities?

Teldat designs its own Regesta Smart family for electrical environments, with more than 60,000 devices deployed in utilities over 15 years. Regesta Smart combines PLC PRIME, broadband over power line, dual-SIM cellular, fiber and Ethernet with integrated SD-WAN, next generation firewall, ZTNA for OT and SCADA protocol inspection, and the Regesta family holds the ENS High category certificate. be.OT adds OT security built into the network equipment, with more than 1,000 industrial protocol signatures, passive asset inventory and one console, helping meet NIS2, CRA and IEC 62443. Specific certifications and capabilities should be verified with Teldat for a given product and software version.

Build a secure, resilient grid with Teldat

Regesta Smart for grid connectivity and be.OT for OT security, from a European manufacturer with ENS High certification and more than 60,000 devices deployed in utilities.

Teldat
Company›